Fuel Injection Adjustment: Difference between revisions
| Line 23: | Line 23: | ||
**Yoshimura Box (Denso FI Adjuster) | **Yoshimura Box (Denso FI Adjuster) | ||
**[http://www.tuneboy.com.au/ Tuneboy] (for Triumph, Benelli, Aprilia) Sagem or Kehin ECU | **[http://www.tuneboy.com.au/ Tuneboy] (for Triumph, Benelli, Aprilia) Sagem or Kehin ECU | ||
*Eprom Chips | *Replacement Eprom Chips | ||
** [http://www.fuelinmoto.com.au/fimprods.html#umchip UltiMap] (for Ducati, BMW, Aprilla, Laverda, Moto Guzzi) | ** [http://www.fuelinmoto.com.au/fimprods.html#umchip UltiMap] (for Ducati, BMW, Aprilla, Laverda, Moto Guzzi) | ||
*Eprom Chip Programing | *Eprom Chip Programing | ||
Revision as of 03:52, 24 October 2006
Motorcycle Fuel Injection
Why Adjustment is Necessary
All stock bikes need to be re-jetted or mapped. Bikes are designed with fuel systems that are compromised so that they can pass noise, emissions, and economy standards around the world. This, not to mention all of the different gasoline formulas available. Performance is usually the last consideration of the factory.
Dynojet's press on the need for adjustment.
The following diagrams are from the book; Bosch Fuel Injection & Engine Management (Probst, 1991). They clearly show that any manufacturer is going to build a system that provides a lean mixture for fuel economy, or just slightly rich for minumum emissions, but far from the rich mixture neccessary for maximum power. Exhaust, intake, and other power enhancing modifications usually contribute to an even leaner mixture. The system must be corrected.


Adjustment Hardware and Software
- Fooler Boxes
- Dynojet's Power Commander
- Cobra's 2000 and 2000R
- Programers
- Replacement Eprom Chips
- UltiMap (for Ducati, BMW, Aprilla, Laverda, Moto Guzzi)
- Eprom Chip Programing
- UltiMap FlashLoads (for Ducati, Moto Guzzi)
- Aftermarket and Kit ECUs
- UltiMap U59 (for Ducati)
The Dynomometer
Comercial and Custom Maps
Usually, on high performance machines the lean conditions programed into the EMS are most pronounced a between 0 and 20 percent throttle opening and in lower rpm's. Goverment test procedures usually point to where the mixture will get leanest. Since the tests are rarely conducted at WOT and near redline, the system is probably running best in that range.
The custom map is next. The standard maps that Dynojet and other manufacturers provide are created using what ever bike happed to be available at the time, in whatever state of tune it happened to be in. By paying a specialty shop, Like Factory Pro to create a custom map for my exact bike, the power is then optimized and throttle response improves greatly.
This map created for me was with stock unmodified exhaust and stock air filter with the fire screen removed. PAIR and SMOG systems have been removed as well. Otherwise, the bike's powerplant remains stock. The bike was dynoed with Mobil 1 EP 15W-50 lubrication (reducing power just slightly), a 520 chain (raising power slightly) and watter wetter coolant (cooling the engine more).
Notice that the bike, stock, was mapped too lean to about 40% throttle, then gets too rich to 100% throttle. This trend will be seen on most bikes. Why? Simple, the bike is lean at first so that the bike will pass emmisions regulations and testing, then it gets rich so that the bike will run well enough, under hard use, if the end user puts an aftermarket pipe on the bike. This is what a power commander will fix.
HERE is the map file.
This is what the Dynojet map looked like. Pretty crazy. You can tell that they just hooked it to the computer and let 'er rip. There is no way a quality map could look like this.
Power Commander Instalation
4 bypass connectors at each of the lower injectors and one bypass connector at the throttle position sensor, then a simple ground to the battery. It is very important to calibrate the throttle position sensor to the power commander when installing. 1% error could make all the difference
Bibliography
- Bosch Fuel Injection & Engine Management. Charles Probst. 1991. Bentley Publishers.
- Motorcycle Fuel Injection Handbook. Adam Wade. 2004. MBI Publishing.