PVD The Girly Bike

This is a special bike for my wife. A mountain bike. She is very light and rides very light. Making a light bike is one thing, getting it to flex just right is quite another.

It's going to be capable of single speed or gears. She's probably not going to ride the bike much, 'cause she likes her suspension bike so much, but this will give us maximum flexibility with just a little more weight for this goofball bike.

The Print

The Tubes

• Top Tube: True Temper OX Platinum #01, 25.4 OD, 620mm, .7/.4/.7
• Down Tube: True Temper OX Platinum #06, 31.8 OD, 680mm, .7/.4/.7
• Seat Tube: True Temper OX Platinum #05, 28.6 OD, 580mm, .7/.4/.7
• Seat Stays: True Temper OX Platinum #SS1
• Chain Stays: True Temper OX Platinum #CS3

• Head tube: Custom machined tube

• Bottom Bracket: Paragon 1.5"
• Drop Outs: Paragon Sliders
• Hydo Stops: Pacenti SS Stamped Bikelugs.com

Successes and Problems

The Good

• The machined head tube looks awsome. It appears that it did not ovalize much at all in the welding process. I am very happy with that part of the project.

• The front triangle looks really neat with the 1" top tube and 1.25" down tube. The head tube/top tube joint is especially cool looking.

• Custom bending of OX Platinum stays is a great success. It took a lot of failure and some improvements on my bending set-up. Things look great in the end.\
• Because I had an issue with seat tube reaming, I made a seat tube sleeve that reduced the post size to 26.0mm, a lot nicer for the lighter rider. Kinda cool looking too.

The Bad

• OX Platinum is REALLY, REALLY, REALY hard after welding. I wasn't able to ream the seat tube. I destroyed a brand new reamer trying. I had to cut it down and weld in a sleeve. Lesson learned. Keep OX Platinum to DTs, TTs, and SSs.
• My welding still looks like shit. It may be the OX platinum causing issues, but most probably more due to the extremely thin wall tubes. I do need much more practice.
• Using the OX Platinum #05 cut down as a seat tube was a really bad idea in more than one way. Welding the super crazy thin (0.4mm) tube at the bottom bracket with complex curves was hell. I made it work, but it ain't pretty.
• I should have bent the chainstays a bit more. Tire clearence is limited to a 2.1" tire.

Repairing the Seat Tube Issue

Please. Look away. This sucks. I know. Hopefully this bike will be replaced in a few months, so this has to only last so long.

I'm really sadened by this fix. It's lame. It's not quite straight. I will try to never have this happen again.

The Paint

It's going to be a cheap powder coat pink. Hopefully the cost will be less than $150.

I have used Poly Engineering of Richmond, CA but may use Olympic Powdercoating for this one. Poly Engineering did an OK job, but it could have been better and their stock color choices could be better as well. I will have to ship the bike, but they have an excellent reputations and a but load of colors to choose from.

The Complete

It doesn't stop at the frame. Note the girly 5" rear rotor! The 26.0 seat post is a nice touch as well.

The Ride

Wow! This is a really different experience.

When I set my wife's full suspension bike up for her, I cannot test ride it. I weigh quite a lot more than she does and I flatten the bike in the parking lot, let alone railing trail. With the suspension nearly bottomed, it is hard to diagnose any problems.

This bike is similar to that in a different way. I tried to test ride this bike around the block. The bottom bracket was swinging from side to side and the wheelbase grew quite a bit as I loaded the bike up and down. I felt scared! It was just wrong.

BUT...

When my wife and I took the bike out on a small test ride, no apparent problems showed up with here on it. I rode behind here up a brutal fire road climb and the frame looked straight and solid. She said the bike felt comfortable and in control. Thus, the goal was acheived, a bike built for a specific rider.

Is it light? Oh my god is it! I need to weigh things properly, but it's about the lightest bike I have ever felt.

She really hates the rigid fork. That will collect dust in time. Smart girl.