Difference between revisions of "Handlebar Preparation"

From Pvdwiki
Jump to: navigation, search
(Make and Install Delrin Plugs)
 
(32 intermediate revisions by the same user not shown)
Line 1: Line 1:
Preparing mountain bike handlebars is quite simple, but easy to do wrong.
+
Preparing mountain bike handlebars is quite simple, but easy to do wrong. The key is to have the ends of the bar end up very rugged, and able to slide against trees and rocks. Sliding is key so that you can actually lean against a rock face with your bar as you pedal. This technique can prevent you from crashing or help you make a section.
  
==Cut to Length==
+
The key to all this is a custom delrin end plug. Here is how:
 +
 
 +
===Cut to Length===
 
I cut my example to about 25.5" These bars will be going onto a singlespeed, so a little wider is better. On a geared bike, I would cut them about an inch or so narrower.
 
I cut my example to about 25.5" These bars will be going onto a singlespeed, so a little wider is better. On a geared bike, I would cut them about an inch or so narrower.
  
 
Cutting handlebars too narrow results in extremely poor handling and leverage against the terrain. Leaving the bars too wide results in bumping trees or bridges too much, plus you are limited in terms of narrowest crossings.
 
Cutting handlebars too narrow results in extremely poor handling and leverage against the terrain. Leaving the bars too wide results in bumping trees or bridges too much, plus you are limited in terms of narrowest crossings.
  
==Square and Clean up Ends==
+
[[Image:Handlebar_5972.jpg]]
==Make and Install Delrin Plugs==
+
 
[[Image:Delrinbarplug.png|100px]]
+
[[Image:Handlebar_5971.jpg]]
 +
 
 +
===Square and Clean up Ends===
 +
[[Image:Handlebar_5974.jpg]]
 +
 
 +
===Make and Install Delrin Plugs===
 +
 
 +
Here is a measured drawing of the part.
 +
 
 +
[[Image:Delrinbarplug.png]]
 +
 
 +
[[Delrinbarplug.pdf]]
 +
 
 +
The 0.765 measurement of the plug on this drawing is the actual size of the bore of the bar. The plug needs to be cut about 0.002-0.003" larger than the bore so that it will be held tight via press fit.
 +
 
 +
I usually make these from white delrin, but this black delrin was convinient, so it was used.
 +
 
 +
[[Image:Handlebar_5977.jpg]]
 +
 
 +
A nice collet lathe makes things very easy.
 +
 
 +
[[Image:Handlebar_5976.jpg]]
 +
 
 +
[[Image:Handlebar_5978.jpg]]
 +
 
 +
The Product.
 +
 
 +
[[Image:Handlebar_5981.jpg]]
 +
 
 +
Hammer the plugs into place and you are good to go!
 +
 
 +
===Special Considerations for Carbon Fiber Handlebars===
 +
 
 +
Due to the varying shape of that ID and the nature of carbon bars, the difference is that that the plug is cut for a more loose fit, then epoxied into place.
 +
 
 +
[[Image:Plastic 5957.jpg]]
 +
 
 +
I choose to use Devcon Plastic Welder 14320. It is about the most insane epoxy for joining plastics.
 +
 
 +
[[Image:Carbonbarend.jpg]]
 +
 
 +
===Off the shelf alternatives===
 +
[http://www.blackspire.com/accessories/bar-end-caps BlackSpire] has one of the best accessories for lock-on grips. It is an end cap for the handlebars as well as clamp for the grip. If you can't do what I describe on this page, look into BlackSpire's quality canadian products.
 +
 
 +
 
 +
[[Category:Controls]]
 +
[[Category:Bicycle]]

Latest revision as of 19:46, 15 December 2006

Preparing mountain bike handlebars is quite simple, but easy to do wrong. The key is to have the ends of the bar end up very rugged, and able to slide against trees and rocks. Sliding is key so that you can actually lean against a rock face with your bar as you pedal. This technique can prevent you from crashing or help you make a section.

The key to all this is a custom delrin end plug. Here is how:

Cut to Length

I cut my example to about 25.5" These bars will be going onto a singlespeed, so a little wider is better. On a geared bike, I would cut them about an inch or so narrower.

Cutting handlebars too narrow results in extremely poor handling and leverage against the terrain. Leaving the bars too wide results in bumping trees or bridges too much, plus you are limited in terms of narrowest crossings.

Handlebar 5972.jpg

Handlebar 5971.jpg

Square and Clean up Ends

Handlebar 5974.jpg

Make and Install Delrin Plugs

Here is a measured drawing of the part.

Delrinbarplug.png

Delrinbarplug.pdf

The 0.765 measurement of the plug on this drawing is the actual size of the bore of the bar. The plug needs to be cut about 0.002-0.003" larger than the bore so that it will be held tight via press fit.

I usually make these from white delrin, but this black delrin was convinient, so it was used.

Handlebar 5977.jpg

A nice collet lathe makes things very easy.

Handlebar 5976.jpg

Handlebar 5978.jpg

The Product.

Handlebar 5981.jpg

Hammer the plugs into place and you are good to go!

Special Considerations for Carbon Fiber Handlebars

Due to the varying shape of that ID and the nature of carbon bars, the difference is that that the plug is cut for a more loose fit, then epoxied into place.

Plastic 5957.jpg

I choose to use Devcon Plastic Welder 14320. It is about the most insane epoxy for joining plastics.

Carbonbarend.jpg

Off the shelf alternatives

BlackSpire has one of the best accessories for lock-on grips. It is an end cap for the handlebars as well as clamp for the grip. If you can't do what I describe on this page, look into BlackSpire's quality canadian products.