PVD NYC

This is a concept bike that I'm trying out. 650c wheels and disc brakes on a fixed gear drive. Designed more for slow speed manuverability and safety than full speed road handling.

Print

Tubes

• Down Tube - 1.250 - True Temper HOXPLAT06, 680mm, .7/.4/.7, 89/51/392/38/110
• Top Tube - 1.000 - Nova CRTT 858, 600mm, .8/.5/.8, 60/51/381/38/90
• Seat Tube - NOVA CMST 460, External Butt Seat Tube, 28.6/30.0 X 460
• Chain Stay, Drive - Dedacciai COM12.5 Road 24mm Chainstay (CXCS_OVST_410), 16/30 OVAL, Straight, [1]
• Chain Stay, Non-drive - Dedacciai COM12.5 Road 24mm Chainstay (CXCS_OVST_410), 16/30 OVAL, Straight, [2]
• Seat Stays - Dedacciai AMSS_16ST .7, 16mm to 10.5mm, 560mm, 0.7mm wall
• Bottom Bracket - Phil Wood 1/2 pitch EBB
• Dropouts - PVD Designed IF Dropouts
• Braze-ons - Pacenti Hydro
• Headtube - PVD Design

PVD 650c Disc Fork

• 340 axel to crown
• 35mm offset
• Paragon thin disc tab, cut and mounted for 140mm rotor
• True Temper Versus MSRDLT 28.6mm, 1.65/1.14 Steerer
• True Temper Platnum HOXPLAT-CS4 27.6x20, .76/.56 Oval Blades
• 1.000"x0.035" struts @ 45 degrees
• Special Alpha Q Star Nut
• Generic 9mm Dropouts w/ Safety tabs
• PVD crown race seat

PVD 'Rise' Stem

• 140mm @ 49 Degree
• 1.250x0.035 tube, custom bent
• 1.125 Steerer Clamp
• 1.250 Split Handlebar Clamp

650c 16 spoke wheels

This is an experiment. 16 spokes on a 32 hole hub/rim. The spokes were going to be configured in a paired configuration, but after some discussions with one of the most notorious wheelbuilders in the country, the dicision was made not to. Gravy said that without a special drilling on both the rim and hub the rim would snake. Not good. A skip spoke pattern, he assured me, would stay true. I may still be too heavy for the wheels, but at least the wheel can make it onto the bike.

As any wheelbuilder knows, the goal of a cross spoke pattern is to have the spkes at maximum tangency to the hub flanges. This reduces the wind up the wheel suffers under the induced torque from driving and braking. For most hubs and rims, a 4 cross pattern is the closest to this limit that can be acheived. Sizing the spokes for 32 4-cross is the same as 16 2-cross, so that gives an idea how the wheel will come together. I will be using butted 2mm spokes and the new DT hex nipples to handle the increased tension in the system.

• Alex R390 571x13 rims
• DT Competition, 2.0/1.8/2.0 Spokes
• DT Hexagonal Nipple, 12mm, Brass

Paint

Urban... hummm.

Parts Spec

• Shimano Ultegra Cranks, Modified for singlespeed use.
• Surly Fixed/Disc rear hub (WTB Single Duty Freehub option)
• Shimano BR505 Road Cable Disc Brakes
• Shimano Deore XT pedals (Fixed), Shimano PD-A520 (Free)
• Shimano Dura-ace 10spd chain
• Headset - Cane Creek IS-2, Black.
• Kalloy Guizzo, 27.2mm 0mm offset seatpost (Thomson option)
• Saddle - Devo saddle
• Kenda Kaliente 650x23c tires
• Shimano XT Centerlock Front Hub.
• Shimano XT Rotors. 140mm front, 140mm rear
• Handlebar - FSA K-Wing Ergo, 31.8mm, 42cm x 145 drop x 90 reach
• Bar Tape - Fi'zi:k Microtex Synthetic, Black
• Post Clamp - Salsa Lip-Lock, 30.0
• Seatpost - Kalloy Guizzo SPC-100, 27.2mm (Option - Easton EC90 Zero Offset)