Shimming Eccentric Bottom Brackets

From Pvdwiki
Revision as of 05:48, 1 December 2006 by PVDisease (talk | contribs) (Greasing and Installing)
Jump to: navigation, search

Recently, I put together a 17" 2006 Zion 660EBB Singlespeed frame.

It has an eccentric bottom bracket with dual locking set screws.

The Problem

After much perseverance, I have managed to solve a simple problem. The problem with this system is that the eccentric doesn't even come close to fitting the shell snug. I have noticed the obvious fact that it has room to rock around like they were two unsuited parts. Which in fact they are!

The shell measures 2.141" to 2.150" (slightly distorted due to welding) - Obviously a shell for a Phil Wood eccentric
The eccentric measures 2.126" (54mm) - Obviously an eccentric for a generic shell.

Why would they do this? Simple, I love the Tawanese (TAIWANESE-ed), A large shell will accomodate either solid eccentric without the need for expensive machining or finish work. Is this the best way to do it? Not at all, but it is profitable and that is what is most important to them.

This will lead to problems in the future if not soon.
Bbshim2.jpg



Bbshim3.jpg
By having a well greased bottom with a snug fit (and mine is, believe me!), the bottom will have much less room to rock around and creek. Also, it will require much less clamping force with two screws (one is never really satisfactory) to keep me in my place. This is nice for long term service, as well as keeping the eccentric from spinning when hitting rocks.

The Standard

Generic sizes most comonly available measure generic 54mm (2.126").

Bushnell Eccentrics (one of the finest made) is and expanding eccentric that is very light. It is also very expensive. It's initial diameter is 2.118" and is designed to expand from 1.120" to 1.125". A very close margin to generic 54mm (2.126").

Phil Wood NFES814 Eccentric and NFBSE8 Shell are designed around a 2.142" size, althought custom versions of this are available.

Easton Sports has another standard used in their shells. Their eccentric measures 2.155"

So the proper ream size of a tandem bottom bracket shell is in question. This would help explain the array of problems that people are having with these.

Reaming the Shell Round

For the best possible fit, I will be reaming the bottom bracket shell round. I have reamed many bottoms, and I suggest grease for most.

I will use an adjustable hand reamer (MSC # 02239135) Industrial size M. This will eliminate the distorted shape and make the shell easier to shim.

The reamer is huge. OAL 410mm.
Bbshim4.jpg

A 12 point socket helps drive the reamer. It may take about 50 rotations, so don't use a rickety setup.



Bbshim5.jpg

The reamer requires the use of a cutting oil as well. Motor oil is fine in a pinch.

After a light cutting pass, the distortion in the shell is obvious.
Bbshim6.jpg

Shiming the Eccentric

I will fill the gap using some stainess steel shim stock. It is best to use a single shim so that it is as thick as it can be for durability sake. I prefer stainless shims over brass for the same reason.

Bbshims.jpg

A 0.010" shim and a 0.0015" shim. In the end, just the 0.010" shim was used and it was a very snug fit.

The greased shim with a bend to help installation
Bbshim7.jpg


Hardware Replacement

The two round head cap screws were replaced with Stainless Steel Cap screws for use with a larger wrench and matirial to grab in a worst-case situation. Now a 5mm allen wrench can be used.



Bbshim10.jpg

Greasing and Installing

Marine Grease. Use marine grease. Its what I use when reaming bottoms.


Test fitting.
Bbshim8.jpg

I also need to find a way to rust proof the edges.
Bbshim9.jpg

Park SPA-2 tool is used to roll the cam.
Bbshim11.jpg

Proudly made in Taiwan.
Bbshim12.jpg